Search found 15 matches
- Sat May 18, 2019 9:11 pm
- Forum: Lambretta Tech
- Topic: New scootopia engine mounts
- Replies: 0
- Views: 4677
New scootopia engine mounts
new scootopia mounts with the smaller holes any good or waste of time ?
- Tue Nov 06, 2018 6:58 pm
- Forum: Standard Scoots & Restorations
- Topic: RUSTORATION ADVICE PLEASE.
- Replies: 9
- Views: 7766
Re: RUSTORATION ADVICE PLEASE.
I am going to do a rustoration on my 1960 series 2, the runners are quite coroded with holes,same as legshields ,but i want it to look as found after being behind a shed since 76.Looked in the m.o.t manual can't see anything about sharp edges, has anybody else done a rustoration with corrosion in p...
- Wed Jan 24, 2018 4:01 pm
- Forum: Lambretta Tech
- Topic: Best Engine Mounts
- Replies: 11
- Views: 4267
Re: Best Engine Mounts
ok thanks , looks like bgm or new scootopia at the mo .
- Tue Jan 23, 2018 6:26 pm
- Forum: Lambretta Tech
- Topic: Best Engine Mounts
- Replies: 11
- Views: 4267
Re: Best Engine Mounts
Thanks for info so far , so the best could be new scootopia , 3-hole indian or BGM that are highly rated at the moment ?
- Tue Jan 23, 2018 4:53 pm
- Forum: Lambretta Tech
- Topic: Best Engine Mounts
- Replies: 11
- Views: 4267
Re: Best Engine Mounts
Bit of a minefield isnt it
- Tue Jan 23, 2018 12:15 am
- Forum: Lambretta Tech
- Topic: Best Engine Mounts
- Replies: 11
- Views: 4267
Best Engine Mounts
Tried most of them thought id give BGM a try next are they currently the best to use , vibration free ?
- Mon Dec 21, 2015 10:35 pm
- Forum: Sports Bar
- Topic: The Song Title Thread - Pointless but Addictive!
- Replies: 25756
- Views: 4643720
Re: The Song Title Thread - Pointless but Addictive!
Midnight Special - Creedence Clearwater Revival
- Thu Sep 03, 2015 10:14 am
- Forum: Standard Scoots & Restorations
- Topic: First scoot & first restoration
- Replies: 52
- Views: 24135
Re: First scoot & first restoration
An observation mate looks like earlier forks looking at the welded on cable guide, why have they been changed in the past i wonder ? Before you paint it i would make sure the frames straight ............................and stick with 6v , just get flywheel remagnetized for good lights again
- Tue Apr 16, 2013 10:03 pm
- Forum: Lambretta Tech
- Topic: Piston to bore clearance
- Replies: 38
- Views: 12120
Re: Piston to bore clearance
ditto- always used Mahle and worked down from 3 1/2 thou to 2 1/2 thou clearance now, with no issues whatsoever. Mix at 3% semi. Loads of short, reasonably hard cycles on rebores and well run in by 300 miles. Chris Hello Chris , on the mahle piston they can stand the tighter clearance so you dont g...
- Tue Apr 16, 2013 8:55 pm
- Forum: Lambretta Tech
- Topic: Piston to bore clearance
- Replies: 38
- Views: 12120
Re: Piston to bore clearance
Af Rayspeed Mahle pistons are the best ive found / always use now, standard type and there beefed up to stop cracking on the skirts , with 200 careful miles running in on flat roads you can do these at 2-2.5 thou , with fully syn at 2% , never had any problems Ditto. Some people laugh when you tell...